Home > Event Id > Event Id 20000 Unable To Find Record For Packet

Event Id 20000 Unable To Find Record For Packet

Your computer is running the TCP/IP protocol. Event ID 1010 - Perflib Symptoms: The Event Viewer may shows Event ID 1010 ""The Collect procedure for the "tcpip" service in DLL "C:\WINNT\SYSTEM32\PERFCTRS.DLL" generated an exception or returned an invalid Use nbtstat -n in a command window to see which name is in the Conflict state. Unauthorized reproduction forbidden. check my blog

You must enable portfast to limit the amount of TCs and subsequent flooding, which can affect the performance of the network. For more information, refer to the Securing the Network Against Forwarding Loops section of this document. Error 4: Event Type: Warning Event Source: BlackBerry Dispatcher STORM2007 Event Category: None Event ID: 20000 Date: 7/17/2007 Time: 8:37:39 AM User: N/A Computer: STORM2007 Description: [SRP] Connection failed Eh, they Offline 07-17-2007, 08:45 AM #6 (permalink) hdawg BlackBerry Genius Join Date: Aug 2006 Model: hdawg PIN: port3101.org Carrier: hdawg Posts: 6,632 Post Thanks: 0 Thanked 0 Times http://www.eventid.net/display-eventid-20000-source-BlackBerry%20Enterprise%20Server-eventno-2593-phase-1.htm

Resolutions: One possible cause of this error is that you have run out of buffer space in the NetBT datagram buffer. Was wondering if anything major is wrong, or any way of getting rid of the errors? Designated root has priority 0, address 0007.4f1c.e847 Designated bridge has priority 32768, address 00d0.003f.8800 Designated port id is 128.129, designated path cost 2000019 Timers: message age 4, forward delay 0, hold Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions This Document Applies to These Products Catalyst 2940 Series Switches Catalyst 2955

Issue the show interface | include line|\/sec command to display only the packet per second statistics and the interface name: cat# show interface | include line|\/sec GigabitEthernet2/1 is up, line protocol Case Study - There are currently no logon servers available to logon your request Event ID: 2011 When accessing shares on a server from a client, you may receive "Not enough Enable the user to allow dial -in. 4. Securing the Network Against Forwarding Loops To handle STP’s inability to deal correctly with certain failures, Cisco has developed a number of features and enhancements to protect the networks against forwarding

Was wondering if anything major is wrong, or any way of getting rid of the errors? Free trial here! This web is provided "AS IS" with no warranties. Your computer is a master browser. https://www.experts-exchange.com/questions/23732583/Blackberry-Exchange-BES-lots-of-errors-and-user-can't-activate.html If the RRAS server is configured only for LAN routing, you can ignore the event. 4.

Please cross-check configuration. 2014 Archival of old events done successfully. Causes: 1. A Demand Dial connection to the remote interface ToChicagoTech on the port VPNx-### was successfully initiated but failed to complete successfully because of the following error: The remote computer did not Causes: 1.

Both client and server have different Authentication Methods. There are specific commands which apply to the Catalyst 6500/6000 only; however, you can apply most of the principles to any Cisco Catalyst switch that runs Cisco IOS software. Error=1450 - Resolution with screenshots Event ID 33919 - The automated credentials test failed for the following server or servers- Resolution with screenshots Event ID 34113: The job failed with the Install the printer drive in the TS server. 2.

All Rights Reserved. click site Event ID 20194 - The reason for disconnecting was user request Hyper-V live migration failed with ID 20201, 20126, 20134 21114, 21502 Event ID 20209 - A connection between the VPN The issue might arise when TCs are occurring repeatedly, with short intervals. NOTE: After you perform these steps, wait at least 10 minutes to see if the errors still occur. 3.

To determine which port is considered the root for a given VLAN, issue the show spanning-tree vlan vlan command: cat# show spanning-tree vlan 333 MST03 Spanning tree enabled protocol mstp Root Resolutions: 1. Windows 2000 domain controllers running Terminal Services configured to use Remote Administration mode do not permit regular user logon, with the exception of two concurrent administrator accounts for server management. news This page has been accessed 2,995 times. © 1992-2015 Cisco Systems, Inc.

To break the loop, you must shut down or disconnect the involved ports. Restore the redundancy. TC shortens the forwarding table aging time on all switches in the VLAN where the TC occurs; thus, if the address is not relearned, it will age-out and flooding will occur

Windows 2003 domain controllers running RDC do not permit regular user logon, with the exception of administrator accounts. 3.

Event ID 1000 and 1001 - Windows cannot read the history of GPOs from the registry - The computer has rebooted from a bugcheck. - Security policy cannot be propagated. - The purpose of STP is to block redundant ports based on an STP algorithm, to resolve redundant physical topology into a tree-like topology. Note:With Rapid STP or Multiple STP (IEEE 802.1w and IEEE 802.1s), TC is triggered by a change of the port’s state to forwarding, as well as the role change from designated Repeat for as many entered.> Custom Details: Groups/Systems: Actions: E-mail

RSS:
Beep:
Net Message:
SNMP:

For every switch on the redundant path, check for these issues: Does the switch know the correct STP root? Resolutions: 1. Look at VLAN interfaces only. More about the author Repeat for as many entered.>Event Filters: Rule

The SSL connection request has failed. Only use this command with ports that connect to end stations. Designated root has priority 0, address 0007.4f1c.e847 Designated bridge has priority 32768, address 00d0.003f.8800 Designated port id is 128.129, designated path cost 2000019 Timers: message age 5, forward delay 0, hold Issue the remote command switch show ibc | i rx_input command on the Catalyst 6500/6000: cat# remote command switch show ibc | i rx_input rx_inputs=5626468, rx_cumbytes=859971138 cat# remote command switch show

Without knowledge of the correct topology, the switch can not block the loops. Contact Us - BlackBerryForums.com - Archive - Top LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread! This can be useful if such incidents needs to be investigated, because BPDU Guard produces the syslog message and shuts down the port. You may want to setup NTP time.

Console User: Active Users: No files added or modified or deleted. 3241 EventTracker has backed up the log file :Security: because its offset has been lost. User: %1 ERROR - description of error 2050 EventTracker patch applied 2050 EventTracker patch applied 2051 Failed to commit CAB file on EventVault.