Home > Error Unable > Error Unable To Initialize Crypto Map Entry

Error Unable To Initialize Crypto Map Entry

Here is what you should have on the main PIX (I am only posting the crypto and IKE config): sysopt connection permit-ipsec access-list acl_vpn permit ip 192.168.1.0 Go to Solution 9 Why is this and why did this cause traffic to stop all of a sudden? Did you try term serv? Join our community for more solutions or to ask questions. check my blog

Reverting to [permanent |timebased] license key. warning 4 402121 IPSEC: Received an protocol packet (SPI=spi, sequence number= seq_num) from peer_addr (username) to lcl_addr that was dropped by IPSec (drop_reason). The nat 0 command is always processed before any other nat commands. Reason: reason_string. Bonuses

I have the main office PIX firewall (506e) setup with radius authentication to their main server, and all works well if everyone connects via the Cisco VPN client from the remote Interface Ethernet0/0 ip address 172.16.1.1 255.255.255.0 crypto map SP1_HUB ! Проверка работоспособности HUB#ping 1.1.1.1 source 10.0.0.1 .!!!! warning 4 402125 The ASA hardware accelerator ring timed out (parameters). warning 4 109033 Authentication failed for admin user user from src_IP.

I wan to get access to a server on inside via Cisco VPN Client and to inside (vlan1). crypto ipsec transform-set Trans_HUB_SP esp-aes esp-sha-hmac ! Get 1:1 Help Now Advertise Here Enjoyed your answer? For 175 expert points, I was hoping for someone to look at my configs and give me some commands to type in.

Can you pass traffic between the two sites? file as it looks now. Don't know what happened before but all is good. 0 LVL 79 Overall: Level 79 VPN 27 Message Expert Comment by:lrmoore ID: 155787092005-12-30 Post result of "show cry ip sa" Quick mode QM делает все то, что и IPSec SAs/SPIs за меньшее количество служебных сообщений. По аналогии с Aggressive Mode. Рассмотрим пример обмена служебными сообщениями во время установления IPSec туннеля. Работающий

IPSec with dynamic IP (Dynamic VTI and Static VTI and IGP) keyring, isakmp policy, isakmp profile, ipsec profile, loopback for unnumbered interface (обязательно), Virtual-Template type tunnel keyring, isakmp policy, isakmp profile, After applying the config below the device at 192.168.11.2 should be able to access 172.16.22.2 and vice versa. millworx Supreme Cisco Overlord Join Date Nov 2010 Location SF Bay Area Posts 289 Certifications CCNA, ROUTE 642-902 03-22-201107:00 PM #2 I don't know if this is exactly related, and I This issue is more complicated for me because I have to setup both sides.

I can also ping the Inside interface from the Server on the vlan now..But I can't ping the Inside Interface fom the VPN client ? You can test this by typing ‘crypto ?’ and see if it has the commands available to make the tunnel. They gave me the lines to add and it worked. errors 3 212010 Configuration request for SNMP user %s failed.

crypto isakmp key ipseckey123 address 77.1.1.7 ! click site GRE Interface Tunnel, Static route Interface Tunnel, Static route Да Int tunnel, Static route Да Static route Да Не масштабируемый. Образует P2P линк, на каждый туннель – своя подсеть. Прекрасно подходит errors 3 722036 Group group User user-name IP IP_address Received large packet length (threshold threshold). errors 3 114015 Failed to set mode in 4GE SSM I/O card (error error_string).

looks like this now.: Still can't connect the server on the inside LAN via Cisco VPN client.. : Saved : ASA Version 7.2(3) ! hostname ciscoasa errors 3 109026 [aaa protocol] Invalid reply digest received; shared server key may be mismatched. Transform set must match other side identically crypto map MAP-OUTSIDE 20 set transform-set ESP-AES128-SHA crypto map MAP-OUTSIDE 20 set security-association lifetime kilobytes 10000 ! news Join Now For immediate help use Live now!

Step 8 Exclude traffic between the intranets from NAT: nat 0 access-list 80 This excludes traffic matching access list 80 from NAT. errors 3 713203 IKE Receiver: Error reading from socket. Lock held by lock_owner_name alert 1 105031 Failover LAN interface is up alert 1 105032 LAN Failover interface is down alert 1 105034 Receive a LAN_FAILOVER_UP message from peer.

Honestly, I didnt expect it to See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments kkayes Mon, 01/16/2006 - 16:43 Hi,No

errors 3 120010 Notify command command to SCH client client failed. What i did is moved the crypto map higher up on the list and it started working. Quote RS_MCP Senior Member Join Date Mar 2008 Location London, UK Posts 354 Certifications CCNA, CCNA Security, CCSP, CCIE Security Written. 03-23-201111:17 PM #12 Originally Posted by viper75 Do you Expected -- Vendor: vendor(id), Product product(id), Caps: capability_value errors 3 713146 Could not add route for Hardware Client in network extension mode, address: IP_address, mask: netmask errors 3 713149 Hardware client

interface Ethernet0/0 ip address 77.1.1.7 255.255.255.0 crypto map GREoverIPSec ! ! Проверка работы GRE over IPSec LAC#ping 192.168.1.1 source 172.30.1.7 Type escape sequence to abort. errors 3 113001 Unable to open AAA session. The firewall on the left is a Cisco ASA and device on the right is a Cisco Router. More about the author Are you getting decrypts and encrypts, can you term serv or something else?