You have a problem with your code. All rights reserved. The second picture - J-Link on STK3300 Board.[/URL][/URL]The first J-Link. J-Link connected Firmware: J-Link compiled Jan 17 2007 14:58:19 ARM Rev.5 J-Link found 1 JTAG device, Total IRLen = 4 JTAG ID: 0x3F0F0F0F (ARM7) ERROR: Unable to halt ARM core ERROR: check my blog
No valid license found. J-Link connected Firmware: J-Link compiled Jan 17 2007 14:58:19 ARM Rev.5 Resetting target using [email protected] and trying again to connect... " And in the console they are: " mi_cmd_stack_list_frames: No stack. example code.Like • Show 0 Likes0 Actions Sapna May 21, 2014 2:53 AMMark CorrectCorrect AnswerI had gone through this document which says issue of start and stop condition using a register Thanks in advance, Regards, Naveen Read-Only AuthorDave Sudolcan Posted11-Jul-2007 14:47 GMT ToolsetARM RE: Unable to Halt ARM Core Dave Sudolcan Hmmm...
At least it matters the value of PINSEL2. You have a problem with your code. Bayes regression: how is it done in comparison to standard regression? Message 6 of 10 (14,434 Views) Reply 0 Kudos gmthomas Super Star Posts: 38 Registered: 10-13-2012 JTAG unable to halt core Options Mark as New Bookmark Subscribe Subscribe to RSS Feed
embedded arm microcontroller cortex-m3 jtag share|improve this question edited Sep 8 '10 at 5:50 starblue 38.8k1163120 asked Sep 3 '10 at 17:56 Supernova 612 Are you sure that main() Related 3Output debug via printf on a Cortex-M3 CPU, stalls at BKPT instruction + confusion about JTAG and sw ports6Advice needed for ARM Cortex M3 beginner5On Freescale iMX31, how can I and it just worked!I can only assume that the Segger on the STK3700 is doing something that the standard J-Link pro isn't but what that might be I don't know. http://www.onarm.com/forum/10200 share|improve this answer answered Sep 30 '10 at 21:46 old_timer 37.9k546100 add a comment| up vote 0 down vote Make sure you have this line in code: WatchdogStallEnable(WATCHDOG0_BASE); // stop the
All Rights Reserved © 2016 Jive Software | Powered by Jive SoftwareHome | Top of page | HelpJive Software Version: 2016.3.4.0, revision: 20161130091729.efc1903.release_2016.3.4 HomeBlogs From the Editor Recent Posts Popular (this None of the other programs I have tried does the same as this one. some idea? Regards Jukka Start a New Thread You might also like... (promoted content) FREE - Atollic TrueSTUDIO C/C++ IDE for ARM VIDEO: Software-Only Motion and Vision Control EtherCAT stalks the industrial automation
also what signals have you wired ?/Mads My views are my own and do not necessarily represent the views of Silicon Labs Message 2 of 10 (14,434 Views) Reply 0 Kudos have a peek at these guys Set breakpoints earlier until you reach the section that causes the lockup.> > Chris. > Thanks Chris for your response. I.e. All categories Device Cloud (245) Python (757) RF Solutions and XBee (5,839) Digi TransPort (368) Digi Connect Cellular (303) Embedded Devices (3,574) Android (31) NET+OS (2,343) Linux (582) Windows CE (82)
But on others, that doesn't happen, and you need to ensure the watchdog is disabled while doing JTAG debugging. EnergyAware Commander display error at upload bin-files in the flash the target CPU.Second J-Link upload without errors.With other MCPU (STM32, for example) the first J-link works without problems. This is a brand new EFM32GG390F1024 so as I understand it should have the UART/USB bootloader programmed in. news I then let it update the firmware in the J-Link (the date was only later by one month) and now everything just works as it should, no problem at all and
the AN-895ADuC702x MicroConverter I2C-Compatible Interface incl. Not the answer you're looking for? However, when I executed my code from main(), I immediately got "CPU is not halted" error, followed by "No APB-AP found" error. I just happened to try using the STK3700 board to connect to the JTAG on our board using passthrough mode.
Cannot tell exact reason, but I guess it had smth to do with fiddling with the screwdriver on the board while having it powered Solution: Using reset pin. Chris. Accept and hide this message /forum/docs/thread10200.asp Thursday, December 22nd 2016, 5:08am UTC+1 You are not logged in. More about the author i used connect-me with devellopement kit and,this time i can't connect jtag to the module...
The JTAG cable is about 4- 5 inches long and the speed about 100K.I was using J-Link software version 4.36e. VECTRESET has confused core.WARNING: CPU did not halt after reset.WARNING: CPU could not be haltedInfo: Core did not halt after reset, trying to disable WDT.WARNING: CPU did not halt after reset.WARNING: